Home
Kathleen's Blog
A FRAMED MONOGRAM SWEATSHIRT!
Sunday, 19 January 2020 09:44

 

framed monogrammed sweatshirt finished

It's not a secret that Kathleen LOVES her some Monograms...

You know...

BIG...JUMBO Monograms...

And since this project is going to be for ME...I wanted to shake it up a bit, by adding some Fabric Bling to the mix!

Reese Witherspoon would be so PROUD of me!

LOL!

Let's get moving...

I started off by choosing the 6x10 inch size of the

Rounded Square Patch Applique from the “Monogrammed Patches” design. 

I set it “on point”

and then added my 3 letters in the 6” size of the Vine Monogram Font on top!

By choosing to start with the Square Patch Applique as a base for my completed design...

I was able to add multiple colors to the mix. 

I chose a pretty Pink and Gray Plaid

and then used HOT Pink Thread for the Vine Monogram on top!

It's a WIN...WIN situation!

Here's my design stats...

-7.85” X 7.85” square

-18,850 stitches

I prepped my 8x8 Full Fast Frame with Sticky Stabilizer

and then found my center of the design

using my rule of thumb of 2” below the neckline to the TOP of the design. 

Once you have the mark for the TOP of your design you can easily find your center. 

I also fused a piece of No Show Mesh Cutaway to the backside of my sweatshirt...

for added permanent control during repeated washing's. 

***TIP...When I make shirts for adults

I usually use the 2” number from the neckline to the Top of the design. 

Baby and Children's garments I use a 3/4” to 1” number from the neckline to the Top of the design (this will depend on how SMALL the baby garment is). 

I like my designs to be up on the chest and not in the middle of the stomach...but that's just a personal preference and you should use what ever design placement strikes your fancy!

Here she goes...

framed monogrammed sweatshirt on the machine

Are you thinking...

Red Clippie OVERLOAD?

I LOVE my Red Clippies from Clover...

and I'm NOT ashamed to use the WHOLE box!

LOL!

As you can see in the above picture...

I have loaded my shirt upside down...

with the waistline going in FIRST to the neck of the machine. 

Therefore...

the design is loaded upside down too! 

This gives me “less stretching” at the neckline of my garment.

Once I had the Applique panel of fabric tacked down and trimmed...

I slapped a piece of WSS on top and let Matilda Jane do her magic...

stitching out all that FABULOUS satin work and triple bean stitch overlay!

Gracious ALIVE...

I LOVE it!

framed monogrammed sweatshirt finished

And just because I “CAN”...

Here's a close up of this Fabulous NEW Monogrammed look...

framed monogrammed sweatshirt close up finished

TOOLS OF THE TRADE...

-Rounded Square Patch (from the Monogrammed Patches Design-I used the 6x10” size and set it on Point)(www.babykaysappliques)

-Vine Monogram Font (I used the 6” size) (www.babykaysappliques)

-Fast Frame (I used the FULL 8x8 inch size)

-Red Clover Clips (Joann's-Hobby Lobby-On Line and Quilt Shops)

-Perfect Stick Stabilizer (I used Floriani Brand)

-No Show Mesh Cutaway Stabilizer (I used Floriani Brand)

-WSS (No Name Brand)

-Pink and Gray Plaid (Joann's)

-Thread (Exquisite Brand) Light Gray #1707 and Hot Pink #325

-Jerzee Brand Sweatshirt (choose your favorite department store or on line store)

-Water Soluble Pen for Marking Center of design


Read 0 Comments... >>
 
A PRETTY FLEECE SCARF!
Saturday, 18 January 2020 00:10

fleece scarf finishedThe Holidays may have come and gone...

but the freezing weather certainly has not left us! 

Almost everyone is experiencing “wintery” days as of late...

and today's project is sure to bring a little warmth on those not so nice moments in time!

Next to wearing a soft pair of Flannel Pajamas...

I gotta say that having a pretty Fleece Scarf runs a close second to being one of my FAVORITES!

Let's get started...

I found this Super Soft Fleece Scarf at my local Walmart...

and they come in several colors, so that gives you more options as to which direction you may want to go with your fabrics!

I have been wanting to use an Appliqued Circle Monogram Font for quite some time now...

and this is the PERFECT project for it!

I decided on the 5 inch size Monogram and placed the bottom of the design 1.5 inches above the area

where the “fringe” starts on the edge of the scarf.  This is really a personal preference...

go with whatever you think looks best for YOU!

I prepped my  7 X 7 inch frame with sticky stabilizer first

and then placed the bottom of my fleece scarf right on the sticky (centering it).

I added a couple of my favorite little red clippies for extra hold! 

Once I have my frame attached to my machine I “floated” a piece of tear away underneath the frame for extra added stability. 

I wanted my backside of my scarf to be almost as pretty as the front side is...

and this stabilizer combination helped me achieve just that!

Here she goes...

fleece scarf satin work

As you see in the above picture...I threw a piece of WSS on top...

just before it starts the satin work. 

I know...

It's a SHOCKER!

My fabric choice is a really pretty piece of orange cotton batik...

I really love the way this particular fabric cuts so crisply

when I am trimming the letters after the tack down stage. 

If you have never used a cotton batik for your applique panels...

be sure to give it a try...you will simply love it! 

And before you ask...

YES...

I still prep the cotton batik fabrics with Heat and Bond Lite on the backside,

just like I do with regular cottons.

Designs Stats...

Overall Size-5” wide X 4 7/8” tall

Stitch Count-11,826

Now...

When I got to the triple bean stitch (which is the back and forth straight stitch on TOP of the satin work)...

I went with the same color orange thread as I used for the satin work. 

I really LOVE the way it gives dimension to my letter...

Without it being a “contrast” in color!

fleece scarf close up bean stitch

How about YOU?

Now...

Isn't she Beautiful?

fleece scarf finished

And...

Just because I know you all want to see the backside of the scarf...

Here's a close-up...

fleece scarf backside finished

Because I used the Floriani Brand of Sticky Stabilizer...

a simple spritz of water allowed me to remove every bit of it...

and the tear away came off easy too!

And...

since I used the same orange thread for the triple bean stitch...

you do not see any pops of a second color on the backside either!

Now...

That's what I call a PLAN!

Kathleen

TOOLS OF THE TRADE...

-Scallop Circle Monogram Applique Font (I used the 5” size) (www.babykaysappliques.com)

-Fast Frame (I used the 7x7 inch size)

-Perfect Stick Stabilizer (I used Floriani Brand)

-Tear Away Stabilizer (off Brand)

-WSS (off Brand)

-Heat and Bond Lite Fusible (Hobby Lobby, Joann's, Walmart and On Line)

-Clover Wonder Clips (Hobby Lobby, Joann's, Amazon and Quilt Shops)

-Fleece Scarf (Walmart)

-Fabric...Orange Cotton Batik (unknown)

-Thread-Exquisite Brand...Lite Orange-#649

-Water Soluble Pen for Marking Center of design


Read 0 Comments... >>
 
MONOGRAM EVERYTHING!
Thursday, 16 January 2020 00:00

flannel shirt hip monogram finished flannel monogram

 

“My rule is...if it's not moving...MONOGRAM it”!

As an Embroiderer...I love this quote from the famous Reese Witherspoon...

but seriously...it describes me PERFECTLY!

No matter where I go...

I am constantly looking for the possibilities of items that can be Monogrammed or Appliqued in some way!

Can I get an Amen?

Let's get going...

I started off with a Super Soft Flannel Shirt, I found at my local Costco store...

if you have never shopped the isles of clothing, towels and bedding in this store...

be sure you do...

the monogramming possibilities are endless there!

This particular Flannel Shirt came in a great variety of colors...

and I may or may not have grabbed one of each. 

But really...

there are Super Cute Monograms and Fonts out there and I simply MUST use them ALL!

Who's with ME?

I'm gonna be gutsy today and place my Monogram on the bottom right corner of my flannel shirt,

and since flannel shirts tend to be a button down styled garment...

it is so darn easy to load this onto ANY machine!

I began by playing around in my Embrilliance Software with the many fonts and monograms

to see what struck my fancy, for this particular shirt. 

I settled on the 3” Sofia Font and chose to be BOLD and use only my First and Last initial. 

I am one of those people with the letter “I” for my middle initial and I don't necessarily LOVE what that looks like...

but it certainly does NOT keep me from finding new ways to...

MONOGRAM EVERYTHING!

Here she goes...

flannel shirt hip monogram on the machine

I have loaded the bottom corner of my shirt onto my 5X7 Fast Frame...

using a Sticky Stabilizer and a piece of NO Show Mesh Fused to the backside.

I also threw a piece of WSS on top before I hit start...

Because...

it's what I do!

My two letter Monogram is about 4.75” wide X 4.5” tall...

with only 5,332 stitches in it...but WOW...she packs a PUNCH!

This particular font is BOLD and using white thread made it pop right off the flannel shirt. 

I am certain...someone will notice!

Be still my heart...

flannel shirt hip monogram finished flannel monogram

AND...

Just because I can...

Here's a close up!

flannel shirt hip monogram close up finish

Now...

Who's ready for some cooler weather...

That would be ME!

Kathleen

TOOLS OF THE TRADE...

-Sofia Font (I used the 3” size) (www.babykaysappliques.com)

-Fast Frame (I used the 5x7 inch size)

-Perfect Stick Stabilizer (I used Floriani Brand)

-Fusible NO Show Mesh (I used Floriani Brand)

-WSS (off Brand)

-Thread (Exquisite Brand) White #010

-Flannel Shirt (Costco)

-Clover Wonder Clips (Hobby Lobby, Joann's, Amazon and Quilt Shops)

-Water Soluble Pen for Marking Center of design


Read 0 Comments... >>
 
SKATING PENGUIN ORNAMENT!
Thursday, 19 December 2019 00:00

finished penguin on skates ornament

Does this Sweet Skating Penguin look familar...

Like you've seen this gal before...

Right?

Truth be told...you have!

YEP...it's the same Applique Design I used for my Flannel Pajamas I made a few weeks ago!

I only made a slight change...by removing the "BRRR" word from underneath.

I LOVE this little gal so...

How about YOU?

I stitched the girly penguin onto a piece of stone colored cotton twill...

it was the PERFECT background for the fabrics and threads I chose for the Penguin itself.  

Be sure to double click the picture to enlarge it so you can see it up close and personal...

and be able to see that glitzy vinyl I used for the scarf and the skates too!

OMG...it's Super Cute!

I also used my go to "stabilizer" of choice for ornamants...Warm and White 100% Cotton Batting. 

I layered it with my cotton twill and then loaded it onto my frame. 

Just as I had done on some of my other Christmas Ornaments...I mounted it onto Sticky Board...

I then added a second slightly larger sticky board...

that was covered with a cute black and white buffallo check cotton fabric.

I also added a glittery silver cording around the edge of the actual stitched piece...

to give it a little POP!

Isn't she just the SWEETEST?

Kathleen

 TOOLS OF THE TRADE...

-Skating Penquin Design...I used the 4X4 size (https://babykaysappliques.com/product/skating-penguin-4x4-5x7-6x10-8x8/)

-Cotton Twill Fabric (stone color)

-Glitter Mirror Vinyl for the Scarf and the Skates (www.mikriworld.com)

-100% Warm and White Cotton Batting (available at Fat Quarter Shop-Joann's-Hobby Lobby)

-Silver Metallic Cording (Hobby Lobby)

-Sticky Board (https://www.fatquartershop.com/16-inch-x-20-inch-pres-on-mounting-board)

-Stitchery Tape (https://www.fatquartershop.com/double-sided-stitchery-tape-60-foot-roll


Read 0 Comments... >>
 
A LITTLE STAR PILLOW ORNAMENT!
Wednesday, 18 December 2019 00:00

finished star quilt ornament

 Gracious BE...

this sweet ornament pillow makes me HAPPY HAPPY HAPPY!

If you are a Quilter in any way...

then this Fabulous little project...is just for YOU!

I used the same Ornament Process Technique to make this Ornament Pillow

as I have in the past with my "flat styled" Christmas Ornaments...

why fix something that isn't Broken?

I digress!

I used a layer of Warm and White 100% Cotton batting underneath the Tan Cotton/Linen Blend fabric...

and then I loaded it onto my frame and then into the machine.

I stitched this Super Cute Snowflake Applique design on to the front of the little pillow...

and then I cut a piece of the same Cotton Linen Blend and layered it together with another piece of batting...

the same size as the front stitched piece is....

By layering a piece of cotton batting with the back fabric helps give the pillow ornament a more firm body...

even before i stuff it with fiber fill.

I added a cute green and red metallic bow and a pretty green jingle bell to the top...

and a simple metallic braided ribbon for the hanger too!

I LOVE it bunches....

how about YOU?

Kathleen

 TOOLS OF THE TRADE...

-Snowflake Applique Design (https://creativeappliques.com/shop/snowflake-applique-2/)

-Cotton/Linen Blend Fabric (tan color)

-100% Warm and White Cotton Batting (available at Fat Quarter Shop-Joann's-Hobby Lobby)

-Metallic Braided Ribbon for the Hanger (Hobby Lobby)

-Red and Green  Metallic Wire Ribbon for the Bow (Hobby Lobby)

-Green

-Fiber Fill Stuffing

 


Read 0 Comments... >>
 
«StartPrev12345678910NextEnd»

Page 3 of 75
 

Schedule

<<  October 2019  >>
 S  M  T  W  T  F  S 
    1  2  3  4  5
  6  7  8  9101112
13141516171819
20212223242526
2728293031  

Contact Me

If you would like to schedule a class or private lesson, drop me an email!

Website Hints

Please click on any picture to see a larger version.  Just use your browser's "Back" button to return to this page.

To leave feedback on a particular blog post, click on "Read # comments..."

Thanks for visiting!